Description

MORTAR STAIN REMOVER 407 highly concentrated fast-acting buy in India.

Mortar Stain Remover is a highly concentrated fast-acting acid-based.

Chemical formulas have 18% strength that dissolves mortar and cement stains.

also remove ingrained dirt, and most paints on mineral surfaces such as brick, render, and concrete.

Clean up after use with cold water.

HIGHLY CONCENTRATED ACID-BASED MORTAR STAIN REMOVER.

Acid-based liquid for powerful cleaning.

Clean stains from brickwork, some natural stone, concrete, and earthenware.

Clean stains from patios, garage, and factory floors.

Everbuild 407 Mortar Stain Remover Building Products Surface Treatments 5 Liters.

SAFETY DATA of MORTAR STAIN REMOVER 407:-

Mortar Stain Remover is an acid-based, highly concentrated fast-acting liquid formula that dissolves mortar and cement stains.

TECHNICAL DATA SHEET OF 407 MORTAR STAIN REMOVER:-

DOWNLOAD TECHNICAL DATA SHEET OF 407 MORTAR STAIN REMOVER.

407 Mortar Stain Remover is an acid-based, highly concentrated fast-acting formula.

407 Mortar Stain Remover can dissolve mortar and remove cement stains.

APPLICATION INSTRUCTIONS.

SUBSTRATE PREPARATION.

May be applied to dirty and damp surfaces.

APPLICATION METHOD / TOOLS.

Always wear impervious gloves, boots, coveralls, and face shield/goggles during use.

Before applying, wet the area in question with water and try an inconspicuous area for compatibility prior to full application.

Cleaning brickwork: Use neat.

Pour the required amount of cleaner into a PLASTIC CONTAINER (do not use metal containers) and apply using a scrubbing brush or a stiff bristle paintbrush, working well into the substrate.

Leave the solution for 20 mins, then scrub with clean cold water until the surface is clean.

Repeat application for extremely stubborn stains. Finally, flood-treated areas with cold water after use.

Cleaning patios:

Use a 1:1 dilution with water (always add acid to water) and apply and rinse as above, testing an inconspicuous area prior to complete application.

EVERBUILD® 407 Mortar Stain Remover CHARACTERISTICS / ADVANTAGES:-

• Acid based – powerful cleaning action.
• Water clean-up.
• Economical in use.

Freezing Point:- 0°C approx.

Active Content:- 17.5-19.5%.

pH:- 1.0 approx.

Odour:- Acrid.

EVERBUILD® 407 Mortar Stain Remover PRODUCT INFORMATION:-

Packaging:- 5ltr and 25ltr plastic containers.

Appearance / Colour:- Thin green/yellow liquid.

Shelf Life:- 24 months when stored according to manufacturers’ instructions.

Storage Conditions KEEP AWAY FROM CHILDREN.

Store at 5 – 25 ºC and away from alkaline products and bleach.

Density:- ca. 1.1 g/cm³.

EVERBUILD® 407 Mortar Stain Remover APPLICATION INFORMATION:-

Yield 1 Litre (neat) will clean approximately 10m² depending on the porosity of the surface, type, and quantity of surface stain.

407 Mortar Stain Remover (EVERBUILD®) LIMITATIONS.

Always read the label before use and wear suitable protective equipment.

Take care when working on interior surfaces and with artificial stone.

ALWAYS test a small area before applying it to the entire surface.

On very sensitive surfaces, a 1:1 dilution as a trial is recommended.

Always wash the surface down after treatment.

Protect plants and animals from contact when using.

Care must be taken with natural stones, as this product can cause carbonation.

VALUE BASE:-

All technical data stated in this Data Sheet are based on laboratory tests.

Actual measured data may vary because of circumstances beyond our control.

LOCAL RESTRICTIONS:-

Note that as a result of specific local regulations, the declared data and recommended uses for this product may vary from country to country. Consult the local.

Product Data Sheet for the exact product data and uses.

ECOLOGY, HEALTH, AND SAFETY.

For information and advice on the safe handling, storage, and disposal of chemical products, users shall refer
to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological, and other safety-related data.

LEGAL NOTES.

The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika’s current knowledge and experience of the products when properly stored, handled, and applied under normal conditions in accordance with Sika’s recommendations.

In practice, the differences in materials, substrates, and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered.

The user of the product must test the product’s suitability for the intended application and purpose.

Sika reserves the right to change the properties of its products.

The proprietary rights of third parties must be observed.

All orders are accepted subject to our current terms of sale and delivery.

Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.